Manual work is very much in fashion and saves money. DIY furniture is easy to build. A bank of pallets, for example, can only be done in a few steps. But when it comes to bedroom design, choosing the perfect furniture is a must. The most important piece of furniture in the bedroom is the bed. Bedroom furniture fails without the bed. It serves the good night’s sleep and ensures your best comfort. The choice of the right bed should therefore be considered very well. Here comes the question: buy bed or build yourself? If you want to customize the bedroom or just the whole apartment, then opt for the do-it-yourself variant! Do not waste money on expensive beds! Instead, you could build a comfortable bed yourself! Take the challenge by building a bed yourself. Simple building instructions can be found in this post!

Build your own bed for your good sleep …



… and your best well-being!



Which bed types are best for self-construction? In addition to box spring beds, bunk beds and water beds you can of course make a single bed yourself. Most beds consist of a frame, slatted frame and mattress. Depending on the size, headboards or bed heads can be added. Wood is the most popular material. These include solid woods such as beech, pine or oak, which are also perfect for home improvement work. When self-building a single bed with a 90 x 200 slatted frame you need the following materials and tools:

12 wooden boards 110 x 10 x 1 cm and 12 wooden boards 220 x 10 x 1 cm;

2 boards 110 x 15 x 1 cm and 2 boards 220 x 15 x 1 cm;

28 wooden blocks 5 x 5 x 5;

4 round rods with 1 cm diameter and 4 wooden balls with 3 cm diameter;

cordless screwdriver; Screws and screwdrivers;

Hammer; Nail; jigsaw; Wood drill or drill;

Sandpaper; Stain; Paint;

How can you build a bed yourself?

Manual:

First of all, think well about the space requirements! He focuses on the design of the bed. In general, the bed should be 20 to 30 centimeters longer, so you feel good!

The highlight of this bed is that the individual components are threaded onto the rods. Above all, it is about pre-drilling boards and wooden blocks. Pierce wooden blocks exactly in the middle completely! Holes on the boards work! Each board should have a hole on each side. Holes are measured from the outer edges 4.5 cm inwards. As a result, the boards later protrude 2.5 cm beyond the wooden blocks. Drill the wood balls in a nutshell! Drill hole only about 1 cm deep! All holes are done!

Start with the construction of the bed! Put the four round bars in four blocks and put these blocks in the appropriate place in the room! Thread two long boards for the short sides of the bed onto the round bars. Thread two long boards at right angles for the long sides of the bed!

Now four wooden blocks, two short boards and again two long boards follow! Assemble bed frame! Combine the head and foot sections as well as the sides with the bed connector to the bed frame! These are helix angles with short leg lengths and a large overall height. Position the fittings so that always the long leg with the short side and the short leg with the long side are screwed!

That’s how it’s built

After the third or fourth wooden blocks thread 15 cm wider boards! These boards continue to protrude into the bed inside, so that the support for the slatted frame is created. Depending on the thickness of the mattress, thread the overlay at the desired height! Select mattress! The choice of the mattress is crucial for your health and sleeping comfort. With overhang, flush or below the bed frame? You decide!

Sand wooden surface! First, break all edges and sandpaper them to create a small chamfer! The visible surfaces with the grinder always in the direction of the wood grain with coarser and then with finer sandpaper! Water surfaces with a sponge! Attention: When drying, loose wood fibers are occasionally found, which you then gently remove with 180 grit sandpaper! Wood is ready for surface treatment!

Stain surfaces! Pickling is about dyeing wood! Apply stain with a fine spray system! By painting the wood gets its surface protection! When building your own bed and processing the bed, it is recommended that you work in a well-ventilated room and avoid smoking, eating and drinking!

Paint surfaces! Fill the paint container in the paint container and dilute with a little water! Apply the first layer of lacquer thinly! Start with the edges and then paint the surfaces!

Ready is your new, individual single bed! Have fun copying!

Build a bed yourself: step by step!

Step 1



step 2

step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Single bed you can easily build yourself!

Depending on your wishes, you could easily make a suspended bed yourself. Cool hanging beds to make your own could be built into your backyard, backyard, living room or bedroom and even on the patio. Hanging beds are very much in vogue. They are practical and flexible, and therefore more and more popular among the residents. An old trampoline and a few tools (hammer and cordless screwdriver, saw and nails), and the suspension bed is ready in just 3 – 4 hours. A light construction manual with pictures follows here.

Step 1

step 2

step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Step 10

Step 11

Step 12

Step 13

Step 14

Step 15

Step 16

Anyone can buy a bed! Do not you mean it? Be different and personalize your home by building a unique bed yourself!


About the author

Heystyles

Leave a Comment